IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
S
ecure mounting bar (D) to outlet box with outlet box screws (not
supplied). Thread nut (E) on nipple (F) so that 3 threads are exposed
above nut (E). Thread nipple (F) into mounting bar (D) and secure with
nut (E).
A. Take note of the color of the wire(s) on your fixture. Identify which
group your fixture wire(s) falls into and connect the wires according
t
o the directions below:
*Note: When parallel wire is used, the tracer wire is square shaped
or ridged and less tracer wire is round in shape or smooth
(Seen best when viewed from wire end). To separate wires, grasp the
ends of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. DO NOT twist wires together
before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and thread the
connector clockwise until you feel a firm resistance.
D. Gently try to remove the wires from the connector, If you can
r
emove the wires, carefully re-do steps B and C, as above and check
again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
GROUNDING INSTRUCTIONS: The gr
een gr
ounding screw (D) is to
be inserted into the hole with two raised dimples pr
ovided on the
mounting bar (A). Wrap the ground wire from the fixture and the
ground wire from the outlet box (bare metal or green insulated wire)
ar
ound the gr
een gr
ounding scr
ew (D) on the mounting bar (A) if
uninsulated wir
e is on the mounting bar (A), connect the gr
ound wir
e
from the fixture and the outlet box to it using a small wire connector
(not supplied).
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.
A
fter the wires are connected, tuck them carefully inside the outlet
box. Push the fixture firmly over the nipple (F) and against the wall.
Secure in place by threading cap nut (M) onto nipple (F).
Make sure no bare wires can be seen outside wire connectors.
I
f installing outdoors, be sure fixture opening is located at the bottom
and see “wet location” note below.
I
nstall lamp (B) by twisting gently into socket (C).
S
TEP 1:
INSTALLATION HC-1380 FINAL ASSEMBLY
STEP 1:
STEP 2:
STEP 3:
CLEANING
ORDERING PARTS
STEP 2:
STEP 3:
Place roof (H) onto cage (A) and secure in place with roof screws (L).
STEP 4:
NOTE: FOR FIXTURES LABELED FOR WET LOCATION AND
USED OUTDOORS.
CATION:
To r
educe the risk of electrical shock, provide a watertight
seal between the fixtur
e and the mounting surface by using a silicone
or similar caulking.
WET LOCATION
Hg
MARK MEANS LAMP CONTAINS MERCURY.
FOLLOW DISPOSAL LA
WS.
SEE WWW.LAMPRECYCLE.ORG
FIGURE 2
FIXTURES WITH A ONE PIECE
LAMP / BALLAST COMBINATION
LAMP (B)
SOCKET (C)
*PARALLEL WIRE (ROUND & SMOOTH) *PARALLEL WIRE (SQUARE & RIDGED)
BLACK WHITE
GROUP A:
CONNECT TO BLACK HOUSE WIRE
GROUP B:
CONNECT TO WHITE HOUSE WIRE
(2 páginas)
(2 páginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais